Autonomic Mirage eSeries Digital Amplifier | 15W x 8 Channels
The M-120e Mirage Digital Amplifier supports four rooms of audio at 30 Watts per zone. Its smaller form factor offers flexibility with placement of the unit, enabling installation into a structured wiring enclosure or wall mounting. The M-120e provides simultaneous amplification for two local source inputs or two eAudioCast™ network streams in as many as 96 rooms.
Wired with a simple Cat5 connection, the M-120e can be placed throughout the home or accessed wirelessly when used with the MMS-1e Mirage Music Streamer.
eAudioCast™
Built-in eAudioCast technology allows eSeries MMS network streams to be transmitted and received, then distributed across zones on each amplifier. Configure a complete, whole-home audio system that is entirely decentralized, residing solely on the network.
High-resolution Audio
All eSeries amplifiers support proprietary Autonomic eAudioCast™, enabling high-resolution audio (HRA), up to 24-bit/192kHz, over Ethernet. The M-120e supports either coax or TOSLINK digital audio on every source input, which allows source material to stay in the digital domain all the way to the final amplification stage, providing reference quality distribution of content all over the home.
Installation Flexibility
The small form factor, eAudioCast technology, and the included mounting accessories afford installers with maximum flexibility in placement. The M-120e can be mounted on a wall near zone speakers, or in a structured wiring can or other enclosure. Distributed eSeries components stream audio and control signals through the home network using a single Cat5 connection to a router or switch.
Virtually Unlimited Zones
Multiple eSeries amplifiers can be utilized in any combination on a single network to support up to 96 zones of high-resolution audio with network-wide grouping capabilities.
Flexible Control Options
Standalone control options include the Mirage Media Controller app for iOS and Android devices, Airplay control, and the Mirage web interface. Plus, pre-programmed control modules are available to integrate major control systems. Refer to the support tab for available drivers.
| AU-M-120E | |
|
Impedance Input
|
0.72V/22KΩ
|
|
Power Output @ 8 ohm
|
15W per channel, 8Ω loads
|
|
Total Harmonic Distortion (THD)
|
<0.1% (10 Watt, 8Ω load)
|
|
Frequency Response
|
20Hz-20kHz
|
|
Adjustments
|
Per-zone adjustments for Bass, Treble, Balance, Loudness, Audio Delay (up to 600ms), Zone Linking
|
|
Dimensions (W x H x D)
|
6.5" x 5.8" x 1.4"
|
|
Inputs
|
(2) Analog source inputs
|
| (2) Digital PCM outputs for zones 1 & 2 | |
| (4) powered speaker channels | |
|
IR Outputs
|
(1) IR transmit for control of third-party devices; 3.5mm jack current limited to 25mA
|
|
Mounting
|
(4) brackets for structured wire cabinet/wall mount
|
|
Operating Humidity
|
10% - 90% RH
|
|
Operating Temperature
|
13°F to 185°F
|
|
Power Consumption
|
79.5W
|
|
Line Voltage
|
100-240V AC Ext DC 15V @ 5.3
|
|
Weight
|
2 lb
|
|
Signal to Noise Ratio
|
96dB (IHA-A, 1V input / unbalanced)
|
|
Nominal Impedance
|
4Ω - 8Ω
|
|
Port Desc.
|
(2) KP-6 in-wall keypad controller ports
|
|
Channels
|
8-Channel
|
|
Zones
|
(4) zones, expandable to 96 zones with additional supported Autonomic amplifiers
|
|
LAN Connection
|
(1) 8-wire RJ45 with 2 LED indicators; 10/100/1000 Mbits/sec BaseT Ethernet port; green LED indicates link status; yellow LED indicates Ethernet activity
|
|
Tone Control
|
±12dB, 100Hz (Bass) ±12dB ,10kHz (Treble)
|
